John McLachlan's Blog: Cadillac ATS Car Key Fob and Remote Programming Instructions

Here at Low Rate Automotive Locksmith we are your source for free instructions on how to program your Cadillac keyless entry remote control and all other kinds of vehicles, both foreign and domestic. Whether you drive a car, a truck, or an SUV we have the information you need to program your remote. Low Rate Locksmith offers detailed step-by-step directions from the manufacturer of your Cadillac car or truck, detailing how to program the key fob remote control, or programmable key for your vehicle. If you have lost a key, replaced a defective key-less entry remote, or added a new key, we have the instructions that you need to make the remote control work for your car, truck, van, or sport utility vehicle. Please select your Year from the menu below.

Here is the list of Cadillac ATS Years and models this supports:

2013 Cadillac ATS

2013 Cadillac ATS Car Key Fob and Remote Programming Instructions:

Program remote transmitter when added, replaced or on system malfunction

How – Without Smart entry system

Remote transmitter can only be programmed using diagnostic equipmentNOTE: Existing remote transmitter memory positions will be overwritten
Obtain and reprogram all remote transmitters
NOTE: A maximum of 8 remote transmitters can be programmed

How – With Smart entry system and one programmed remote transmitter available

NOTE: A maximum of 8 remote transmitters can be programmed
Obtain all remote transmitters
NOTE: Switch ignition OFF
Place all programmed remote transmitters within in the cup holder
Insert key of the unrecognized remote transmitter into driver’s door lock
Turn key to unlock position 5 times within 10 seconds
- Driver’s information center will display READY TO LEARN ELECTRONIC KEY #2, 3, or 4, etc
Place the new, unrecognized remote transmitter into the center console remote transmitter pocket with remote transmitter button facing down and key ring at the rear
Press and release the ignition switch. Driver’s information center will display READY FOR FOB X
Remove remote transmitter from remote transmitter pocket and press remote transmitter UNLOCK button
Repeat above procedure starting with placing the next unrecognized remote transmitter into the remote transmitter pocket until all remote transmitters have been programmedNOTE: To exit programming mode press the OFF/ACC button (ignition switch) for 15 seconds.

How – With Smart entry system and no programmed remote transmitter available

Obtain all remote transmitters
Note: Switch ignition OFF
Insert key of unrecognized remote transmitter into driver’s door lock
Turn key to unlock position 5 times within 10 seconds
- Driver’s information center will display REMOTE LEARN PENDING, PLEASE WAIT
- After 10 minutes Driver’s information center will display PRESS ENGINE STARTBUTTON TO LEARN
Press the OFF/ACC button (ignition switch)
- Driver’s information center will display REMOTE LEARN PENDING, PLEASE WAIT
- After 10 minutes Driver’s information center will display PRESS ENGINE START BUTTON TO LEARN
Press the OFF/ACC button (ignition switch)
- Driver’s information center will display REMOTE LEARN PENDING, PLEASE WAIT
- After 10 minutes Driver’s information center will display PRESS ENGINE START BUTTON TO LEARN
Press the OFF/ACC button (ignition switch)
Driver’s information center will display READY FOR REMOTE #1
Place the new, unrecognized remote transmitter into the remote transmitter pocket with remote transmitter buttons facing the front of the vehicle
Press and release the OFF/ACC button (ignition switch). Driver’s information center will display READY FOR REMOTE # X
Remove first remote transmitter (FOB 1) and press a button to finalize
Carry out above procedure, starting with placing next urecognized remote transmitter into remote transmitter pocket, repeat for all remaining remote transmitters
When allremote transmitters have been programmed driver’s information center dislays MAXIMUM # ELECTRONIC KEYS LEARNED and will exit programming mode
Press the OFF/ACC button (ignition switch) for 10 seconds to exit programming mode
NOTE: Remote transmitters can also be programmed using diagnostic euipment

Immobilizer

without iriginal master key

Keys can only be programmed using diagnostic equipment with original master key

Insert master key into ignition switch
Switch ignition ON
Switch ignition OFF
Remove master key
Within 5 seconds insert new key and switch ignition on
System LED will extinguish
New key now programmed
NOTE: A maximum of 10 keys can be programmed using the master key

with smart entry

System operation – Arms after ignition switch is turned to LOCK/OFF
Remote transmitter added or replaced, or system malfunction
NOTE: Immobilizer is programmed during remote transmitter programming procedure

If you have any questions or need a professional Locksmith To assist you with your Cadillac ATS Key Fab Programming, below is a list of Low Rate Locksmith Locations.

For All other Cadillac Key Fob programming instructions visit this page and Cadillac ATS car key replacement

For more about Cadillac ATS car key replacement Click Here
MORE MORE KEY FOB INSTRUCTIONS CLICK HERE

Cadillac ATS Car key Programming Locksmith Lincoln ca	Cadillac ATS Car key Programming Locksmith Rocklin ca	Cadillac ATS Car key Programming Locksmith Roseville ca
Cadillac ATS Car key Programming Locksmith Folsom ca	Cadillac ATS Car key Programming Locksmith Carmichael Ca	Cadillac ATS Car key Programming Locksmith Citrus Heights CA
Cadillac ATS Car key Programming Locksmith Fair Oaks ca	Cadillac ATS Car key Programming Locksmith Elk Grove CA	Cadillac ATS Car key Programming Locksmith Stockton CA
Cadillac ATS Car key Programming Locksmith San Diego Ca	Cadillac ATS Car key Programming Locksmith San Francisco Ca	Cadillac ATS Car key Programming Locksmith Walnut Creek CA
Cadillac ATS Car key Programming Locksmith Sacramento CA